All Products - Page 95 of 440 - iGAM

(855) 678-4426

View All Results

View All Results

(855) 678-4426

View:

Sort By:

ASCO NUMATICS S1055400028AMO Rodless Pneumatic Actuator, Bore: 40mm, Stroke: 28" NEW 0

ASCO NUMATICS S1055400028AMO Rodless Pneumatic Actuator, Bore: 40mm, Stroke: 28″ NEW

$380.00

Availability:

1 in stock

SKU: IGAM3580030

This listing is for a NEW ASCO Numatics S1055400028AMO rodless pneumatic actuator. It is designed for linear motion applications requiring a compact footprint and extended travel without an exposed piston rod. This unit is a rodless pneumatic cylinder with a magnetically coupled carriage, configured with a 40mm bore and 28 inch stroke, and is commonly used in industrial automation, material handling, and OEM machinery where precise pneumatic positioning is required.

CO‑AX MK‑25‑DR‑NC Coaxial Solenoid Valve 24VDC USED 0

CO‑AX MK‑25‑DR‑NC Coaxial Solenoid Valve 24VDC USED

$380.00

Availability:

1 in stock

SKU: IGAM3580249

This listing is for a USED CO‑AX MK‑25‑DR‑NC coaxial solenoid valve. It is designed for controlling the on/off flow of liquids in industrial fluid handling systems. This unit is categorized as a direct‑acting coaxial solenoid valve and includes normally closed operation, 24 VDC coil, high‑pressure capability up to 40 bar, and threaded process connections suitable for hydraulic or process fluid applications using mineral oil.

PARKER RG2HM0361 HMI Series Rod Gland Kit 36mm NEW 0

PARKER RG2HM0361 HMI Series Rod Gland Kit 36mm NEW

$380.00

Availability:

1 in stock

SKU: IGAM3580146

This listing is for a NEW Parker RG2HM0361 HMI Series Rod Gland Kit. It is designed for use in Parker HMI series hydraulic cylinders to service or replace the rod gland assembly on cylinders with a 36 mm rod diameter. This unit is categorized as a hydraulic cylinder repair component and includes sealing and gland components required to maintain proper sealing, alignment, and performance in industrial hydraulic applications.

FSP PL‑R1‑PE‑35‑P2‑000‑V‑ACE Cartridge Filter NEW (4‑Pack) 0

FSP PL‑R1‑PE‑35‑P2‑000‑V‑ACE Cartridge Filter NEW (4‑Pack)

$380.00

Availability:

1 in stock

SKU: IGAM3580062

This listing is for a NEW FSP PL‑R1‑PE‑35‑P2‑000‑V‑ACE cartridge filter set. It is designed for industrial liquid filtration applications requiring reliable particulate removal and extended service life. This unit is categorized as a pleated cartridge filter and utilizes polyester filter media with a nominal 35‑micron rating. The listing includes four unused cartridges supplied together as a single lot.

New Arrival

ALLEN-BRADLEY 2198-DB42-F Kinetix 5700 Line Filter 42A NEW 0

ALLEN-BRADLEY 2198-DB42-F Kinetix 5700 Line Filter 42A NEW

$375.00

Availability:

2 in stock

SKU: IGAM2781692

This listing is for a NEW Allen-Bradley 2198-DB42-F Kinetix 5700 line filter. The 2198-DB42-F is designed for use with Kinetix 5700 motion control systems to reduce conducted electrical noise and improve power quality in servo drive installations. This unit features a 42A current rating and is intended for industrial automation, motion control, and drive system applications.

FESTO DPA-63-10 Semi-Rotary Pneumatic Actuator USED 0

FESTO DPA-63-10 Semi-Rotary Pneumatic Actuator USED

$375.00

Availability:

1 in stock

SKU: IGAM4160011

This listing is for a USED Festo DPA-63-10. The actuator converts pneumatic energy into limited-angle rotary motion for positioning, indexing, clamping, and material handling applications. Configured with a 63 mm actuator size and 10° rotation angle, the unit includes an attached Festo JH-5/2-D-2-C directional control valve for pneumatic actuation and control.

SIEMENS 6SN1118-0DM33-0AA2 SIMODRIVE 611 Digital Control Module USED 0

SIEMENS 6SN1118-0DM33-0AA2 SIMODRIVE 611 Digital Control Module USED

$375.00

Availability:

1 in stock

SKU: IGAM4160052

This listing is for a USED Siemens 6SN1118-0DM33-0AA2. The SIMODRIVE 611 Digital Control Module provides motion control, drive coordination, and interface functions within SIMODRIVE 611 drive systems. Equipped with multiple communication and control interfaces, the module supports CNC machine tools, servo systems, and industrial automation platforms requiring coordinated drive control and system integration.

SIEMENS 6SL3210-5HE10-8UF0 SINAMICS S210 Servo Drive USED 0

SIEMENS 6SL3210-5HE10-8UF0 SINAMICS S210 Servo Drive USED

$375.00

Availability:

2 in stock

SKU: IGAM1240151

This listing is for a USED Siemens 6SL3210-5HE10-8UF0. As part of the SINAMICS S210 platform, this servo drive provides motion control and power conversion for compatible servo motor systems in automated machinery, positioning equipment, and precision motion applications. The unit supports 200-240 VAC or 380-480 VAC three-phase input and is rated for use with 750 W servo motors.

HAKO MINUTEMAN MC830534 Floor Buffer Burnisher 20in USED 0

HAKO MINUTEMAN MC830534 Floor Buffer Burnisher 20in USED

$375.00

Availability:

1 in stock

SKU: IGAM3780080

This listing is for a USED Hako Minuteman MC830534 floor buffer and burnisher. This corded single-disc floor machine operates on 120 VAC power and is rated at 14 amps (1680 watts). The machine is equipped with a large polishing deck, adjustable operator handle, and heavy-duty motor assembly for floor finishing, polishing, scrubbing, and maintenance applications.

ACCUWEB 4X6U-4060-01 Sensor Edge Detector NEW 0

ACCUWEB 4X6U-4060-01 Sensor Edge Detector NEW

$375.00

Availability:

1 in stock

SKU: IGAM4120157

This listing is for a NEW AccuWeb 4X6U-4060-01 Sensor Edge Detector. It is designed for web guiding, edge position detection, and material tracking applications in converting, printing, packaging, and roll-to-roll processing equipment. This unit is categorized as an Edge Detection Sensor and features a 4 x 6 inch sensing window, non-contact edge detection capability, integrated cable connection, and compatibility with AccuWeb web guide control systems. The 4X6U-4060-01 is commonly identified in industrial markets as a sensor edge detector or double sheet detector for precision web alignment applications.

SEW-EURODRIVE SA47/TDRS71M4 Helical Gearmotor USED 0

SEW-EURODRIVE SA47/TDRS71M4 Helical Gearmotor USED

$375.00

Availability:

2 in stock

SKU: IGAM2840425

This listing is for a USED SEW-EURODRIVE SSA47/TDRS71M4. This helical gearmotor combines an AC motor with an integrated gear reducer to deliver controlled torque and reduced output speed for industrial drive applications. The unit features compact inline gearing, three-phase operation, and a foot-mounted configuration suitable for conveyors, material handling, and general machinery requiring reliable speed reduction and power transmission.

PILZ 301131 106434 1.4 PSS SB Bridge SafetyBus Interface Module NEW 0

PILZ 301131 106434 1.4 PSS SB Bridge SafetyBus Interface Module NEW

$375.00

Availability:

3 in stock

SKU: IGAM2840394

SMC CNA2F63TF-320-D Pneumatic Tie-Rod Air Cylinder 63mm Bore 320mm Stroke USED 0

SMC CNA2F63TF-320-D Pneumatic Tie-Rod Air Cylinder 63mm Bore 320mm Stroke USED

$375.00

Availability:

1 in stock

SKU: IGAM3580088

This listing is for a USED SMC CNA2F63TF-320-D pneumatic air cylinder. It is designed for linear motion and force generation in industrial pneumatic systems. This unit is categorized as a tie‑rod style, double‑acting air cylinder and features a 63 mm bore size, a 320 mm stroke length, and a maximum operating pressure of 1.0 MPa (145 PSI). The SMC CNA2 series is commonly used in automation equipment, production machinery, and OEM pneumatic assemblies where reliability and standardized mounting are required.

SMC CNA2F63TF-300-D Pneumatic Tie-Rod Air Cylinder 63mm Bore 300mm Stroke USED 0

SMC CNA2F63TF-300-D Pneumatic Tie-Rod Air Cylinder 63mm Bore 300mm Stroke USED

$375.00

Availability:

1 in stock

SKU: IGAM3580082

This listing is for a USED SMC CNA2F63TF-300-D pneumatic air cylinder. It is designed for linear motion and force generation in industrial pneumatic systems. This unit is categorized as a tie‑rod style, double‑acting air cylinder and features a 63 mm bore size, a 300 mm stroke length, and a maximum operating pressure of 1.0 MPa. The SMC CNA2 series is commonly used in automation equipment, production machinery, and OEM pneumatic assemblies where ISO‑style mounting and reliable performance are required.

SIEMENS 3RK1207‑1BQ40‑0AA3 Analog Input Module NEW 0

SIEMENS 3RK1207‑1BQ40‑0AA3 Analog Input Module NEW

$375.00

Availability:

1 in stock

SKU: IGAM3580157

This listing is for a NEW Siemens 3RK1207‑1BQ40‑0AA3 AS‑Interface compact analog input module. This unit is designed for decentralized field‑level analog signal acquisition and supports two analog current inputs for industrial sensors. The module is part of the Siemens SIRIUS K60 series and is rated IP67 for operation in harsh industrial environments. It is commonly used in machine automation systems requiring reliable 4–20 mA signal processing over AS‑Interface networks.

KUKA ESC‑C13 V1.60 Control PCB Board A161.00.005.571 USED 0

KUKA ESC‑C13 V1.60 Control PCB Board A161.00.005.571 USED

$375.00

Availability:

1 in stock

SKU: IGAM3680029

This listing is for a USED KUKA ESC‑C13 V1.60 control board A161.00.005.571. It is designed for robotics control and signal interfacing within KUKA robotic systems, providing multi-channel communication, relay switching, and I/O distribution through integrated connectors, fuses, and onboard control electronics.

CanFab 1107-EC-HEE HVAC Economizer Assembly USED 0

CanFab 1107-EC-HEE HVAC Economizer Assembly USED

$375.00

Availability:

2 in stock

SKU: IGAM2740211

This listing is for a USED CanFab 1107-EC-HEE. This economizer assembly provides outside air intake and modulation for commercial HVAC rooftop units, incorporating motorized dampers and provisions for enthalpy-based control using Honeywell Jade systems for energy-efficient ventilation and temperature management.

GORBEL SS‑99003 Jib Crane 250 lb Capacity USED 0

GORBEL SS‑99003 Jib Crane 250 lb Capacity USED

Availability:

1 in stock

SKU: IGAM2740018

This listing is for a USED Gorbel SS‑99003 jib crane rated for a 250 lb lifting capacity. This unit is designed as a floor‑mounted jib crane with a rotating horizontal boom used for localized material handling. Gorbel jib cranes are commonly installed in industrial and manufacturing environments to assist with light‑duty lifting, positioning, and maintenance tasks at individual workstations.

See photos for details.

Part No: SS-99003
Type: Jib Crane
Condition: USED

Capacity: 250 lbs
Manufacturer: Gorbel
Application: Material handling / lifting assistance

HARDINGE TTA001194403 Tool Holder Block USED 0

HARDINGE TTA001194403 Tool Holder Block USED

$375.00

Availability:

3 in stock

SKU: IGAM0450538

This listing is for a USED Hardinge tool holder block, part number TTA001194403. The component is a precision‑machined steel tooling block manufactured by Hardinge Inc. in Elmira, New York, USA. It is designed for mounting or holding tooling in lathe or turning applications and features a hardened body with threaded mounting holes and an integral toothed shaft interface. This type of tooling block is commonly used in Hardinge machine tool systems and OEM machining setups.

FESTO CMMT‑AS‑C5‑11A‑P3‑PN‑S1 Servo Drive USED 0

FESTO CMMT‑AS‑C5‑11A‑P3‑PN‑S1 Servo Drive USED

Availability:

16 in stock

SKU: IGAM1701107

This listing is for a USED Festo CMMT‑AS‑C5‑11A‑P3‑PN‑S1 servo drive. This unit is designed for precise motion control of AC servo motors in industrial automation systems. The drive supports PROFINET communication and is intended for use in machine automation, positioning applications, and OEM motion control platforms. The CMMT‑AS series is engineered for compact cabinet installation and high‑performance servo operation.

SAUNDERS 050-56-24-A-11R-D1 Sanitary Diaphragm Valve Assembly NEW 0

SAUNDERS 050-56-24-A-11R-D1 Sanitary Diaphragm Valve Assembly NEW

$375.00

Availability:

2 in stock

SKU: IGAM3540182

This listing is for a NEW Saunders 050-56-24-A-11R-D1 sanitary diaphragm valve assembly. This valve is designed for controlled shutoff and flow regulation of process media in sanitary and hygienic piping systems. The assembly features a manual handwheel operator, diaphragm‑actuated valve design, and flanged process connections, making it suitable for applications requiring cleanability, product isolation, and repeatable operation in industrial process environments.

FUJI ELECTRIC VKA667AQ Coolant Pump 1.1 / 1.8 kW NEW 0

FUJI ELECTRIC VKA667AQ Coolant Pump 1.1 / 1.8 kW NEW

Availability:

1 in stock

SKU: IGAM0650143

This listing is for a NEW Fuji Electric coolant pump, model VKA667AQ. This three‑phase industrial pump is designed for continuous coolant circulation in CNC machines and manufacturing equipment. The pump is rated at 1.1 kW at 50 Hz and 1.8 kW at 60 Hz and features a vertical multi‑stage construction suitable for machine tool coolant systems.

HARDINGE Cam Box Assembly with Gearmotor NEW 0

HARDINGE Cam Box Assembly with Gearmotor NEW

Availability:

1 in stock

SKU: IGAM0450477

This listing is for a NEW Hardinge cam box assembly supplied crated with an attached gearmotor drive. This type of assembly is used in machine tool mechanisms requiring cam-driven motion and timing functions within Hardinge equipment. The unit includes an integrated gear speed reducer and 3‑phase induction motor rated 1.5 HP / 1.1 kW with 220/380 VAC operation for industrial machine tool service replacement and OEM parts support.

HARDINGE NV 000310088J Cam Box Assembly NEW 0

HARDINGE NV 000310088J Cam Box Assembly NEW

Availability:

1 in stock

SKU: IGAM0450475

This listing is for a NEW Hardinge NV 000310088J cam box assembly. Hardinge NV 000310088J is an OEM machine tool component identified as a CAM BOX and supplied crated for service replacement or integration within Hardinge equipment. This assembly is used in cam-driven machine mechanisms where controlled mechanical motion and timing functions are required in industrial machine tool systems.

ICC FR-A7N-ETH Ethernet Multiprotocol Communication Interface NEW 0

ICC FR-A7N-ETH Ethernet Multiprotocol Communication Interface NEW

$375.00

Availability:

5 in stock

SKU: IGAM3540161

This listing is for a NEW ICC FR-A7N-ETH Ethernet multiprotocol communication interface. The card installs directly into compatible Mitsubishi FR-A700 series drives and provides Ethernet-based connectivity for monitoring, configuration, control, and integration with industrial automation networks.

GRUNDFOS CRK2‑30/3 U‑W‑A‑A‑UUV Vertical Multistage Pump USED 0

GRUNDFOS CRK2‑30/3 U‑W‑A‑A‑UUV Vertical Multistage Pump USED

$375.00

Availability:

1 in stock

SKU: IGAM3540010

This listing is for a USED Grundfos CRK2‑30/3 vertical multistage centrifugal pump, type U‑W‑A‑A‑UUV. It is designed for industrial fluid transfer and pressure boosting applications, providing consistent flow and head performance in compact installations. This pump is rated at 0.75 HP, operates at 3500 RPM, and delivers up to 13.2 GPM with a maximum head of 91 ft. The unit is made in the USA, includes an integrated Grundfos motor, and shows cosmetic wear consistent with industrial use.

BOSCH REXROTH 0‑608‑830‑166 SM 24V I/O Interface Module NEW 0

BOSCH REXROTH 0‑608‑830‑166 SM 24V I/O Interface Module NEW

$375.00

Availability:

5 in stock

SKU: IGAM2840249

This listing is for a NEW Bosch Rexroth 0‑608‑830‑166 SM 24V module. It is designed for use in Rexroth industrial automation and drive control systems as a 24 VDC interface / I/O add‑on module. This unit is categorized as an interface module and is commonly used to expand or support control and signal processing functions within Bosch Rexroth servo and automation platforms.

TR ELECTRONIC 110‑00001 CE65M Absolute Rotary Encoder USED 0

TR ELECTRONIC 110‑00001 CE65M Absolute Rotary Encoder USED

$375.00

Availability:

1 in stock

SKU: IGAM2840267

This listing is for a USED TR Electronic 110‑00001 CE65M rotary encoder. It is designed to provide absolute position feedback for industrial automation and motion control systems. This unit is categorized as an absolute rotary encoder and includes programmable resolution up to 4096 steps per revolution, SSI output with RS‑422 signal level, and a wide 11–27 VDC supply range suitable for OEM machinery and control applications.

ANSUL RED LINE CR MX 150 C WHEELED FIRE EXTINGUISHER USED 0

ANSUL RED LINE CR MX 150 C WHEELED FIRE EXTINGUISHER USED

Availability:

1 in stock

SKU: IGAM1460014

This listing is for a used Ansul Red Line wheeled fire extinguisher.
Portable wheeled dry chemical fire extinguisher unit with hose and nozzle assembly.

See photos for details.

Manufacturer: Ansul
Series: Red Line
Model: CR-MX-150-C
Type: Wheeled Fire Extinguisher
Condition: USED
Includes: Hose and nozzle assembly, wheeled cart frame

DENGENSHA TRCN-4030529 C-Type Weld Gun USED 0

DENGENSHA TRCN-4030529 C-Type Weld Gun USED

Availability:

1 in stock

SKU: IGAM2630005

This listing is for a used DENGENSHA TRCN-4030529 Weld Gun.
Industrial welding gun designed for automated or manual welding applications.

Item is clean and was removed from a working system. See photos for details.

Part No: TRCN 4030529
Type: Weld Gun
Condition: USED

Please message us with any questions.